Special purpose dies are threading dies built for non-standard thread forms, pitches, diameters or tolerances that catalog dies don’t cover. Where a stocked die cuts a common metric or unified thread, a special die is ground to your drawing or sample so the external thread on your part matches what your design actually calls for. This guide explains how special dies differ from standard ones, which thread forms they cut, and when it makes sense to specify a custom die.
What Are Special Purpose Dies?
A special purpose die is a thread cutting die made for an external thread that standard catalog tooling can’t produce. That might be an unusual thread form, a nonstandard pitch, an oversized diameter, or a tolerance your application demands beyond a general-purpose product.
Catalog dies serve the common metric and unified threads most shops cut every day. Special dies fill the gap when your part specifies something else. Taylor Tool, a Canadian manufacturer established in 1918, makes special taps, reamers and dies, and works with customers from the smallest job shops to the largest industrial manufacturers.
This article is a supporting guide. For the full range of tooling, see the main dies page. For one of the most common asymmetric forms, see Taylor Tool’s page on special buttress dies.
Special Purpose Dies vs. Standard Threading Dies
Standard dies cover common stocked threads; special dies are made to your drawing or sample. The practical difference comes down to where the specification originates and how readily the tool can be sourced.
| Factor | Standard threading die | Special purpose die |
|---|---|---|
| Thread form | Common metric and unified | Acme, trapezoidal, buttress, Whitworth, BSPT, BSPP, PG and other non-standard forms |
| Availability | Typically stocked | Made to order |
| Specification source | Published standard | Your drawing or sample |
| Pitch and diameter | Standard sizes | Unusual pitches, oversized or large-diameter, left-hand, multi-lead |
| Typical use | General fastening threads | Application-specific threads that mate with a defined part |
If a stocked die matches your thread, use it. If it doesn’t, a near-enough substitute risks poor fit with the mating part. That’s the point at which custom threading dies earn their place.
Common Special Thread Forms Dies Can Cut
Taylor Tool builds tooling for Acme, trapezoidal, buttress, Whitworth, BSPT, BSPP and PG thread forms, among others general suppliers don’t stock. Beyond form, the shop can also address unusual pitches, oversized or large-diameter threads, left-hand threads and multi-lead forms.
| Thread form | Typical application |
|---|---|
| Acme threads | Power transmission under bidirectional, moderate loads |
| Trapezoidal threads | Bidirectional power transmission |
| Buttress threads | High thrust in one direction |
| Whitworth | Parts specified to Whitworth standards |
| BSPT / BSPP | Pipe threads, tapered (BSPT) and parallel (BSPP) |
| PG thread | Conduit and cable-gland style fittings |
| Left-hand thread | Applications where rotation or loosening direction requires it |
| Multi-lead thread | Faster axial travel per turn |
For the internal-thread side of these forms, see Taylor Tool’s special trapezoidal taps page, and for the external side of buttress, the special buttress dies page.
Buttress Threads: A Closer Look
Buttress threads are asymmetric and designed to carry high thrust loads in one direction. The load-bearing flank is steep, while the trailing flank is steeper still to ease disengagement.
Per Taylor Tool’s specification, the standard buttress form uses a 7° load flank and a 45° trailing flank, though custom angles can be specified for unique load profiles. ANSI B1.9 defines common buttress pitches, but many applications need a custom pitch and diameter combination.
| Thread type | Load flank angle | Trailing flank angle | Primary use |
|---|---|---|---|
| Buttress | 7° | 45° | One-direction high thrust |
| Acme | 14.5° | 14.5° | Bidirectional moderate loads |
| Trapezoidal | 15° | 15° | Bidirectional power transmission |
Typical applications include hydraulic cylinders, breech mechanisms and heavy-duty clamps, where force acts consistently in one direction. Choose buttress when axial load is unidirectional and load capacity per unit of thread engagement matters most. Choose Acme or trapezoidal when loads reverse.
When to Specify a Custom Die Instead of a Standard One
Specify a custom die when no stocked die matches your thread form, pitch or tolerance. If a catalog die can cut the thread your drawing calls for, there’s no reason to custom-make one.
Consider a custom die when:
- Your thread form is unusual. Buttress, Acme, trapezoidal, Whitworth, BSPT, BSPP or PG forms often fall outside general stock.
- You run repeat production. A tool ground to your exact specification gives consistent threads across a run.
- Mating-part fit is critical. The external thread must pair with a specific internal thread or component.
- You’re replacing obsolete tooling. If the original die is no longer available, a custom die can be built from your sample.
To request a quote, contact Taylor Tool and describe your thread requirement. Having a drawing or a sample of the part or thread on hand will help the team understand what you need.
Taylor Tool’s engineering team works from your drawing or sample, whether you need a modified standard or a completely unique tool. For matched tooling across a job, ask about custom sets.
Special Dies, Rethreading and Hand-Threading Use Cases
Thread dies cut or restore external threads on rods, bolts and shafts, while taps do the equivalent work inside a hole. If you’re searching for thread cutting dies, rethreading dies or a way to cut external threads, the principle is the same: the die shapes the thread form onto the outside diameter of the workpiece.
The conceptual split is simple. Dies produce external threads; taps produce internal threads. A complete threaded joint usually needs both, matched to the same form and pitch.
Rethreading is the repair use case: cleaning up or restoring damaged external threads so a nut or fitting engages properly. If you need a die suited to rethreading, or you’re deciding on a particular die style for hand use versus machine use, ask Taylor Tool about the options for your application rather than assuming a specific type is available.
For the full line of external-thread tooling, visit the dies page. For internal threads in non-standard forms, see special thread taps.
Pairing Special Dies with Matching Taps
A matched die and tap ensure the internal and external threads mate correctly. If you cut an unusual form on a shaft with a special die, the nut or tapped hole must be cut to the same form, pitch and tolerance, or the joint won’t seat properly.
Taylor Tool produces both sides. Explore special-purpose taps and special buttress taps to complement a custom die. For job-matched tooling, ask about custom sets. The engineering team works from your drawing or sample so the die and tap are specified together rather than as separate guesses.
Why Source Special Dies from a Canadian Manufacturer
Taylor Tool manufactures special taps, reamers and dies at 4 Goebel Avenue in Cambridge, Ontario. As a manufacturer rather than a reseller, it controls quality end to end.
The company supplies automotive, aerospace, power generation and general manufacturing customers, from small job shops to the largest industrial manufacturers, with fast, on-time shipments. In Canada, Taylor Tool sells through a network of distribution; the sales team can direct you to your nearest distributor. For U.S. customers, call the U.S. line at 1-855-221-8277. Taylor Tool is also expanding its U.S. sales representation, so contact the sales team for current information. To learn more about the company, visit the about us page.
Frequently Asked Questions
What are special purpose dies? Special purpose dies are threading dies made for non-standard thread forms, pitches, diameters or tolerances. They’re ground to your drawing or sample rather than pulled from a catalog, so the external thread matches your design.
How do special purpose dies differ from standard threading dies? Standard dies cover common stocked threads. Special dies are made to order for forms, pitches or tolerances that catalog tooling doesn’t offer, using your drawing or sample as the specification.
What thread forms can a special die cut? Taylor Tool builds tooling for Acme, trapezoidal, buttress, Whitworth, BSPT, BSPP and PG forms, plus unusual pitches, oversized or large-diameter threads, left-hand threads and multi-lead forms.
Can special dies be made from a drawing or sample? Yes. Taylor Tool’s engineering team works from your drawing or sample, whether you need a modified standard or a completely unique tool.
When should I order a custom die instead of a standard die? Order custom when no stocked die matches your thread form, pitch or tolerance, or when repeat production, mating-part fit or obsolete tooling calls for a tool built to your exact specification.
How do I request a quote for a special die? Contact Taylor Tool and describe your thread requirement, ideally with a drawing or sample of the part or thread. The team can then advise on what’s needed to quote your tool.
What is the difference between a die and a tap? A die cuts or restores external threads on the outside of a part. A tap cuts internal threads inside a hole. A mating joint usually needs both, matched to the same form and pitch.
What is a buttress thread and why is it used? A buttress thread is asymmetric, with a 7° load flank and a 45° trailing flank. It carries high thrust in one direction, which suits hydraulic cylinders, breech mechanisms and heavy-duty clamps.
Can special dies be used for rethreading damaged threads? Dies are used to cut or restore external threads, which is the basis of rethreading. For the right die style for your repair or hand-threading need, ask Taylor Tool about options for your application.
Does Taylor Tool ship special dies to the United States? Yes. Taylor Tool is expanding its U.S. distribution network. Call 1-855-221-8277 for U.S. ordering information, lead times and availability in your region.
What industries use special purpose dies? Taylor Tool supplies automotive, aerospace, power generation and general manufacturing customers, from small job shops to the largest industrial manufacturers.
How do I order Taylor Tool products in Canada? Taylor Tool sells through a network of distribution partners across Canada. Contact the sales team and they’ll connect you with your nearest distributor for pricing and availability.
Ready to specify a special die? Request a quote or call 1-800-265-2145 (Canada) or 1-855-221-8277 (USA).


